Duenne is not an offiicial seller for

NZM2-4-XIPK – EATON

NZM2-4-XIPK – Contact protection, IP2X, 4p, size 2
EATON 266774
SUPPLY PROGRAM
accessories
IP2X protection against contacts
Number of conductors
4-pole
accessories
IP2X protection against contacts
use with
NZM2 (-4), PN2 (-4), N2 (-4)
usable for
For shell terminals
Note
The designation includes parts for a top or bottom switch side for 4-pole switches.

Increased protection against accidental contact to IP2X.

Protection of the connection compartment with cables connected to the shell terminal.

With 2 conductors with a maximum section of 25 mm 2 or AWG4.

Not combinable with NZM-XSTK auxiliary circuit connection.

DESIGN VERIFICATIONS ACCORDING TO IEC / EN 61439
IEC / EN 61439 design verifications
10.2 Suitability of materials and components
10.2.2 Corrosion resistance
The requirements of the product standard are met.
10.2 Suitability of materials and components
10.2.3.1 Resistance of the enclosure to heat
The requirements of the product standard are met.
10.2 Suitability of materials and components
10.2.3.2 Resistance of insulating materials to normal heat levels
The requirements of the product standard are met.
10.2 Suitability of materials and components
10.2.3.3 Resistance of insulating materials to extraordinary heat levels
The requirements of the product standard are met.
10.2 Suitability of materials and components
10.2.4 Resistance to UV radiation
The requirements of the product standard are met.
10.2 Suitability of materials and components
10.2.5 Lifting
Not relevant as the whole electrical panel needs to be evaluated.
10.2 Suitability of materials and components
10.2.6 Impact test
Not relevant as the whole electrical panel needs to be evaluated.
10.2 Suitability of materials and components
10.2.7 Lettering
The requirements of the product standard are met.
10.3 Degree of protection of the enclosures
Not relevant as the whole electrical panel needs to be evaluated.
10.4 Air and surface dispersion routes
The requirements of the product standard are met.
10.5 Protection against electric shock
Not relevant as the whole electrical panel needs to be evaluated.
10.6 Flush mounting of devices
Not relevant as the whole electrical panel needs to be evaluated.
10.7 Internal circuits and connections
It is the responsibility of the manufacturer of the electrical panel.
10.8 Connections for conductors introduced from outside
It is the responsibility of the manufacturer of the electrical panel.
10.9 Insulation characteristics
10.9.2 Dielectric strength at mains frequency
It is the responsibility of the manufacturer of the electrical panel.
10.9 Insulation characteristics
10.9.3 Impulse withstand voltage
It is the responsibility of the manufacturer of the electrical panel.
10.9 Insulation characteristics
10.9.4 Verification of enclosures in insulating material
It is the responsibility of the manufacturer of the electrical panel.
10.10 Heating
The superheat calculation is the responsibility of the electrical panel builder. Eaton provides equipment dissipation data.
10.11 Resistance to short circuit
It is the responsibility of the manufacturer of the electrical panel. Observe the default values of the equipment.
10.12 EMC
It is the responsibility of the manufacturer of the electrical panel. Observe the default values of the equipment.
10.13 Mechanical function
For the device, the requirements are met if the information in the installation instructions (IL) is observed.
TECHNICAL DATA ACCORDING TO ETIM 8.0
low voltage electrical appliances (EG000017) / Breaker wiring set (EC002050)
Technique Of Ar., Electr., Energy, Tecn. Switchgear, Network & Pipeline Processes / Low Voltage Switching Technology / Power Switches (Ns, <1 Cv) / Wiring set for circuit breaker (ecl@ss10.0.1-27-37-04-24 [ACN957011 ]) suitable for number of poles 4 Typology other

From: 15,00  EXCL.

Disponibile

Bestsellers: